LiteGallery

How to Balance Aperture, Shutter Speed and ISO

Hero illustration for the article “How to Balance Aperture, Shutter Speed and ISO”
Published
Reading time
6 min read

Balance aperture, shutter speed and ISO by choosing the exposure you need, then adjusting the other two settings to compensate. Aperture controls depth of field, shutter speed controls motion, and ISO affects image noise.

Start with the effect that matters most: a wide aperture for a blurred background, a fast shutter speed to freeze movement, or a low ISO for cleaner detail. Then adjust the remaining settings until the exposure looks right.

There is no single ideal combination. The best balance depends on your subject, the available light and what you want the photograph to show.

Exposure choices by shooting priority
Priority Starting choice Main trade-off
Freeze motion Fast shutter, such as 1/1000 Less light reaches the sensor
Show motion blur Slower shutter, such as 1/30 Movement becomes less sharp
Shallow depth of field Open aperture to a lower f-number Less of the scene stays in focus
More light in low light Try f/1.8 or f/2.8 Depth of field becomes shallower
Sunny-day film starting point Set f16; match shutter speed as closely as possible to film ISO or ASA Rule is specific to the stated sunny-day film situation
  • f/1.8 or f/2.8 Example apertures that can help avoid raising ISO too high in low light

What should you set before taking the first test frame?

Set Aperture Priority, ISO 200 with Auto ISO off, and the lens’s lowest available f-number; then take a test frame and check its brightness and shutter speed.

In Aperture Priority, you choose the lens opening and the camera selects the shutter speed. This is a useful starting mode when depth of field—the range of the image that appears in focus—is your first concern.

  • For more light and a shallow focus range: open the lens to its lowest available f-number, such as f/1.4 on a fast lens or f/3.5 on a slower lens.
  • For a controlled starting point: set ISO to 200 and turn Auto ISO off. The camera will still choose a shutter speed based on your aperture and the available light.

After the test frame, inspect two things: whether the exposure looks bright enough and whether the selected shutter speed suits your subject. If it is too slow to keep the subject sharp, adjust your settings before continuing.

How do you expose a low-light scene without losing the subject?

In Aperture Priority, open the lens to admit more light, then use Auto ISO limits and a minimum shutter speed to keep the subject sharp without sacrificing more depth of field than you intend.

Keep the subject sharp

Aperture Priority lets you choose the aperture while the camera selects a shutter speed. Opening up to f/1.8 or f/2.8 can save you from raising ISO too high. Turn on Auto ISO and set a maximum ISO and minimum shutter speed so the camera has defined limits.

Choose focus depth before widening the aperture

For a portrait or another still subject, decide how much of the scene should remain in focus before opening the aperture further. A wider aperture admits more light, but it also reduces the area that appears sharp.

  • If the subject is still: Choose the aperture for the focus depth you want, then let Auto ISO work within the limits you set.
  • If the subject is moving: If the selected shutter speed is too slow, raise ISO or use a wider aperture rather than accepting unwanted blur.

What settings freeze motion or deliberately blur it?

A fast shutter speed such as 1/1000 second freezes movement, while a slower speed such as 1/30 second makes moving subjects blur. The fast exposure lets in less light, so shutter speed changes may require an adjustment to aperture or ISO.

  • Freeze movement: Try 1/1000 second. If the image is too dark, open the aperture or raise ISO to let in or record more light.
  • Show motion blur: Try 1/30 second. Hold the camera steady if you want the background to stay sharp while the moving subject blurs. If the image is too bright, narrow the aperture or lower ISO.

How do aperture and ISO change depth of field and image noise?

Aperture controls both how much light reaches the sensor and how much of the scene stays in focus, while ISO affects image noise; shutter speed balances the exposure when either changes.

A wider aperture uses a smaller f-number, lets in more light and creates shallower depth of field—the range that appears sharp. Check that the important parts of your subject, such as the eyes in a portrait, remain in focus. A narrower aperture keeps more of the scene sharp but reduces incoming light, so you may need a slower shutter speed or higher ISO.

Balance exposure and noise

  • Open the aperture: For the same exposure, use a faster shutter speed to offset the extra light. The reduced depth of field may leave parts of your subject out of focus.
  • Raise ISO: A higher ISO can help you keep a faster shutter speed, but may make image noise—visible grain or speckling—more noticeable.
  • Slow the shutter: Compensate with a narrower aperture or lower ISO to maintain the same exposure. A slower shutter can also record motion blur.

How does film exposure change the starting procedure?

For sunny-day film exposure, Lomography recommends setting the aperture to f16 and choosing the shutter speed closest to the film’s ISO or ASA rating.

Check the film’s box or canister for its ISO or ASA marking before setting the exposure: that rating determines which shutter speed to choose. This is a film-specific starting rule, not a replacement for the digital procedure of using Aperture Priority with ISO 200 and Auto ISO off.

For lighting other than a sunny day, follow camera or film guidance suited to your particular setup.

When do these exposure choices fail to solve the problem?

Aperture Priority can still produce a blurred frame when the camera chooses a shutter speed that is too slow for your moving subject.

Check the trade-off in the viewfinder.

  • Shutter speed: Check the speed the camera selects before photographing motion; Aperture Priority does not guarantee a motion-free frame.
  • Aperture: Opening the lens wider can brighten the image, but it narrows the depth of field—the range that appears sharp. Focus carefully on the part of the subject that must be sharp.
  • ISO: Raising ISO can let the camera use a faster shutter speed, but noise may become more visible in the image.
  • Auto ISO: Its limits help only when the minimum shutter speed suits the subject and the maximum ISO suits the image quality you need. Check both limits and the selected values before a critical frame.

Frequently asked questions

What setting should I change first when a moving subject is blurred?
Choose a faster shutter speed, such as 1/1000, to freeze motion. If the frame darkens, open the aperture or raise ISO.
Should I raise ISO or open the aperture in low light?
If you can accept shallower depth of field, opening to f/1.8 or f/2.8 can reduce how much you need to raise ISO.
What does 1/30 do to a moving subject?
A shutter speed of 1/30 can create motion blur. Whether that is useful depends on whether you want to show movement or keep the subject sharp.
What is a simple digital starting point?
Use Aperture Priority, set ISO to 200 with Auto ISO off, and begin at the lens’s lowest available f-number. Check the shutter speed before taking the frame.

Sources

  • photographylife.com — “Understanding ISO, Shutter Speed and Aperture – A Beginner's Guide”
  • myfavouritelens.com — “Understanding (and Using) ISO, Aperture, And Shutter Speed”
  • A Cheat Sheet For Beginners — “ISO, Aperture & Shutter Speed”
  • chriswright.photography — “Mastering Aperture ISO and Shutter Speed – Chris Wright Photography”
  • kolarivision.com — “Kolari | A Complete Beginner’s Guide to Understanding Aperture, Shutter Speed, and ISO”

More in Technique